Wire wrapping feathers at Instructables

I figured out how to make the Instructables process less painful: I discovered and set up the automagic import-pictures-from-Flickr thing. That was nice!

So: Method 1

And: Method 2

Check those out if you would rather read them there (or download them as PDFs!) than in my really long post.

Also – very exciting! – they are currently “Featured” projects on Instructables’ front page.

I’ve thought about trying to videotape the process, too. As if I have the time to mess around with that; I just know I’d get sucked into all sorts of fancy video-editing things, but it might make things more understandable than flipping back and forth between pictures and text.

Share/Bookmark

Wire wrapping feathers

For some strange reason – well, a couple of strange reasons, actually – I have a lot of feathers, and limiting myself to gluing them to things is kind of, well, limiting. Especially if I want to make dangly earrings, or necklaces, or or things, with them.

Wire wrapping seemed like the easiest way to make dangly things with them. I can’t recall if I found any examples online before I got started (my first page of Google hits now doesn’t turn up any particularly good tutorials), so let’s just say I made it up as I went along.

I have a lovely photoset at Flickr, with instructions, or you can read it all right here. (One of these days, I may also make an Instructable, but when I started one a week or two ago, the interface was so aggravating that I gave up.)

First, you need the following tools and materials:

  • round-nose pliers*
  • flat nose pliers*
  • wire cutters
  • feathers
  • very thin wire (I used 26 gauge)

I tried two different methods. The first starts by forming a loop (with one short end and one long end) in the wire, to hang the feather from, and then wrapping wire down the shaft of the feather, trapping the short end of the wire against the feather shaft. The second starts by wrapping wire UP the shaft of the feather, again trapping wire against the shaft, then forming the hanging loop, and finishing by wrapping the remaining wire back down the shaft. I like the first method better, but both seem to create a pretty firm connection between the wire and the feather, though I didn’t try REALLY REALLY HARD to pull the feathers free.

So. On to the wrapping:

Measuring the wire by jfeathersmith.

Because this was a tiny feather (OMG do not use a tiny feather for your first try) I wanted to have almost as much straight wire held against the feather as there was bare feather shaft. It seemed like it would be the strongest way to wire the feather, and aesthetically appealing.

Measuring the wire (2) by jfeathersmith.

I grabbed the wire with the round-nose pliers where I wanted the straight part to end, and the loop (to hang the feather from) to begin.

Make a wire loop by jfeathersmith.

I wrapped the long end (still attached to the spool, because I like making life more complicated) around the pliers to complete the loop.

Completing the loop by jfeathersmith.

Then I bent the long end back around the short straight end, to start the wrapping of wire around the straight wire plus - in a moment - the feather.

Another view of the loop by jfeathersmith.

Another view of the loop

Is the length right? by jfeathersmith.

I checked to make sure I still had the right length of wire to hold next to the shaft, and finally cut the long wire free of the spool, so I had about 2 inches of wire to wrap -around- the shaft and short end.

Preparing to wrap the feather by jfeathersmith.

Why you should not use a tiny feather: Because holding the thin wire and the thin shaft together tightly while also wrapping thin wire AROUND them both is a pain in the butt. Holding the short wire and the shaft really tightly with pliers helped some (yes, it squashed the shaft. in fact I think it broke it a bit. it doesn't matter; you can't see it when you're done).

Examine this loop by jfeathersmith.

See that tiny loop of wire wrapped around the straight wire? Adjust that slightly if necessary so that it is just big enough to hold the very end of the feather shaft. That helps with the final wrapping.

Another view of the shaft-holding loop by jfeathersmith.

Another view of the loop

Grasp firmly and wrap by jfeathersmith.

I gave up on the pliers because I couldn't get coordinated enough to manage and just pinched the feather+wire together tightly with my fingers. Having fingernails helps. Once I had the short piece of wire and the feather closely aligned, and the shaft of the feather just butting against the loop, I wrapped the long piece of wire around and around the shaft+wire combo.

Wire-wrapped feather earring by jfeathersmith.

Connect the feather to an earring loop, and you are done!

Thus endeth the lesson.

I didn’t keep the above earring; that’s just for photographic purposes. I wrapped another tiny feather and made these:

Feather and labradorite earrings by jfeathersmith.

Feather and labradorite earrings. I have some tiny beads made from labradorite; in the right light, they show a blue "flash" that matches the feathers.

I also made an earcuff with a feather dangle, but those photos will be another post, because I have several other earcuffs I want to post at the same time.

Here is method 2 for wire wrapping a feather, but I didn’t like the results as well:

A larger feather by jfeathersmith.

This time, I started wrapping near the fluffy part of the feather, not at the end of the shaft. I didn't want to wrap the entire bare shaft, because it was fairly long. I still wanted about half an inch of overlap between wire and feather, so I formed a loop about that far from one end of the wire (which I cut this time before starting! I CAN HAS LEARNINGS). This loop is not for hanging the feather, it will go around the shaft about half an inch from the end.

Forming the bottom loop by jfeathersmith.

Forming the first loop

Insert feather into loop by jfeathersmith.

I placed the loop in the right position against the feather.

Wire held against feather by jfeathersmith.

Another view of the wire and feather held together

Starting the wrapping by jfeathersmith.

I again found it easier to start wrapping by holding the thing in my fingers. Here I have wrapped the wire around the feather+short wire once.

Ready to finish wrapping by jfeathersmith.

With the larger feather, and more shaft to work with, this time I found it easy to grab the wire and feather with the flat-nose pliers, and wrap the remaining wire around by hand. Part of the trick is that the wire is thinner than the feather shaft, so to hold both together, you really have to squash the feather. Otherwise, that dang wire will slide all over the place.

Wrapping in progress by jfeathersmith.

Don't worry about how the short wire is not tight against the shaft. As you wrap the long wire around them both, it will pull the shaft and short wire together. You will need to move the pliers out of the way; by this point, you don't need a death grip on the assembly, so you can place them over the wrapped section and hold firmly, just not so firmly you flatten things out.

Nearly done by jfeathersmith.

I didn't get the wire positioned quite where I wanted, as there is a short bit of it sticking past the shaft. That can be clipped off.

Make the hanging loop by jfeathersmith.

Now I have just enough wire left to make a loop to hang the feather from. I'm not wrapping to the very end of the shaft right now, because I will finish that after making the hanging loop.

Preparing to make the loop by jfeathersmith.

I straightened out the wire so that it will be easier to wrap part of it against the shaft after I make the loop.

Making the hanging loop by jfeathersmith.

I used the round-nose pliers to make a loop at the end of the shaft. The bare bit of the shaft end, and the wire next to it, will be wrapped with the remaining wire.

Complete wrapping by jfeathersmith.

I grabbed the loop with the flat-nose pliers, and wrapped the remaining wire back down the shaft, trapping the straight wire against it.

Wire-wrapped feather by jfeathersmith.

Finished!

* Some asides about pliers: Really, you could do this all with a single pair of needle-nose pliers, the kind you get at a hardware store. You won’t be able to get perfectly round loops, but if you don’t mind the look of a square-ish loop, go for it (I don’t have photos of this). You could also form the loop by wrapping the wire around a thin stick, like a bamboo skewer; the pliers just help hold the wire still while you wrap it. Also: most pliers not intended for jewelery-making have ridges/serrations on their jaws. These will mar the wire, which is a look you  might like, but if not, wrap some tape (electrical, duct, whatever) around the serrated parts to protect the wire.

Origami Easter

Despite having prettier kleenex boxes around this year (same pattern as last, but blue or pink or purple), I decided not to repeat last year’s Easter basket. I went for origami as the easiest way to make a container to hold tasty chocolate treats.

Easter basket with butterfly and chick

I used this basket pattern, plus the baby chicken and butterfly patterns from Kunihiko Kasahara’s Creative Origami (the book I learned origami from, many years ago), to make the origami pieces. The paper for the baskets came from my endless supply of gently used wrapping paper; the paper for the chick and butterfly came from my supply of actual origami paper, which remains a surprisingly consistent size over the years.

I filled the baskets with crumpled tissue paper and a variety of foil-wrapped eggs. The blue tissue bundles hold malted eggs, and ended up forming part of the support for the butterflies.

Origami Easter basket with butterfly and chick

I used the tissue bundles to support the butterflies, by pushing one end of a flat toothpick into the twist of the bundle, and the other end into the folds of the butterfly’s body (no puncturing of paper necessary; the folds are tight enough to hold the toothpick, as long as you don’t jostle the arrangement!).

I didn’t plan this out carefully in advance; I started with “I’ll make baskets with an origami fold and tissue paper fill.” Then I thought it needed something more interesting to decorate it with because I didn’t buy any little toys, and chicks are traditional (that is the 2nd fold I ever memorized) . . . and a butterfly would be a nice touch and oh hey I bet if I stuck a toothpick into the folds of the butterfly I could prop it up better instead of just setting it on top of everything, and from the right angle it’ll look like it’s flying! Hey, look, those tissue bundles might come in handy.

I also thought about making an origami flower, but I didn’t like the look of any of the folds. So the butterfly is going to have to find another place to get breakfast.